Water Tanks | Water Storage | Chemical Storage

Water, chemical and oil Storage Tanks from up to 90,000 litres in one piece GRP tanks, suitable for storing many liquids including potable water and hot water up to 100 deg C and can be supplied with or without Insulation of varying thickness, We have a large standard range of sizes in our tanks and can make customer specific sized tanks when requested.

Our tanks come complete with a bolted lid and are free standing and require no other support apart from being installed on a flat fully supporting base.

We Also manufacture open top free standing tanks up to 3000mm long and wide.

For most applications and for tanks situated outside with no access restrictions Our One Piece GRP Storage tanks are the ideal solution. These tanks have no internal supports or joints and a smooth internal gelcoat surface these are some of our most economical tanks.  The tanks can be manufactured plain or with insulation, the internal surface resists bacterial growth and all steel supports and externally fixed to the tank walls and encapsulated within layers of fibreglass where required.

One piece tanks can be manufactured using one of three different resins:

• Standard Tanks (Water up to 35 C, Very mild chemicals)
• F & E Tanks (Water up to 70 C, Mild chemicals)
• Chemical Tanks (Water up to 100 C, chemicals)
• Key Benefits
• No Internal Supports or Joints
• Smooth internal bacteria resistant surface
• Lids can be Apexed to cope with Rain/Snow loads if required
• Insulated tanks available with HCFC Free Foam
• Economical costs compared to Sectional Tanks
• Manufactured to BS EN 13280: 2001

These Tanks with no internal supports, Designed for projects where access may have some restriction (e.g. Standard doorways), these tanks can be separated into two halves along their height for access through the doors and corridors, then can be easily erected once in position. These tanks are an excellent alternative to Sectional panel tanks saving in some cases up to 50%.

Two Piece Tanks have been designed to provide a cost effective solution for tanks that need to go through a restricted access but also costs less than a Sectional tank, These tanks are split along their height allowing them to come apart and be taken through doorways and corridors and similar pathways, These tanks have a smooth internal gelcoat surface and no internal supports.

Key Benefits:

• No internal supports
• Smooth internal bacterial resistant surface
• Lids can be Apexed to cope with Rain/Snow loads if required
• Insulated tanks available with HCFC Free Foam
• Cost effective solution to Sectional tanks
• Manufactured to BS EN 13280: 2001

When an area to be used for sitting a tank has restricted access (e.g. doorway or hatch) and therefore a one piece tank could not get access, the only solution left is a tank made from panels and sealed, bolted and assembled in the area once through the restricted access, this allows for a tank with a larger storage capacity to be used in the same area and can be far greater than the access into the area will allow.

Made from GRP tank panels usually 1000*1000mm the panels can be easily moved into position and assembled into a tank by our team of specialists within the area with only 500mm space around the tank.

Sectional Tanks are available plain or with insulation, and are constructed from a number of GRP panels that are bolted and sealed together on site, these tanks can be completely internally flanged only requiring as little as 50mm around the tank to assemble, also tanks that are externally flanged with either internal or external flanged base, all sectionals come complete with sectional lid and Inspection hatch, Sectional tanks with internal bases require a flat fully supporting base where as an externally flanged based sectional can be assembled on pillars or RSJ’s that are all the same level and flat but must be a minimum of 500mm off the floor.

Key Benefits:

• Ideal For tanks that are to be situated through a restricted access
• Insulated tanks available with HCFC Free Foam
• 1000 *1000mm Panels available as standard, Specific panel sizes available on request
• Tanks up to 3m in Height with no restriction on Length and Width
• Manufactured to BS EN 13280: 2001

Many accessories are available from ourselves including Equilibrium Ball Valves, Aylesbury float valves, Screened Overflows and screened vents, BSP Connections, Laminated Stub Flanges, Ball Valve Housings, Screened Spill over Weirs (Type AB Airgap), Lockable Hatches, Kiosks and Housings, Drip Trays and Epoxy Resin Liner.

We can supply a various range of accessories which is listed below, for more details on any of the accessories please contact us.

Range of Accessories:

• Aylesbury Float Valves
• Ball Valves
• Screened Overflows Kits & Vents
• Access hatches (Raised/Hinged/Locked)
• GRP Ball Valve Housings
• Screened Spill over Wiers
• Type AB Airgaps (CAT 5 Backflow prevention)
• GRP Split / Flat Lids
• GRP Drip Trays
• UPVC Tank Connectors
• Brass BSP Essex Connectors
• NP16 Stub Flanges

www.draytontank.co.uk